1000 Watt Dump Load Resistor

This divert load resistor is for use to divert the excess power being generated when your wind turbine generator batteries are full and can be ran at 100% duty cycle due to the quality double wire wound design. It can also be used with a solar array...

5 Blade Dual with Smart Boost MPPT Charge Controller Kit

We've paired our 5 Raptor G5 Blades with our dual core PMG to provide a kit that's suitable for a variety of wind speeds.  The Raptor G5 Blades are whisper quiet, made of a carbon fiber composite with UV protectant, and intended for fast rotation...

Freedom 7 Blade with Smart Boost MPPT Charge Controller Kit

We've paired our reliable 7 Raptor G4 Blades with our single core PMG to provide a kit that's suitable for a variety of wind speeds.  The Raptor G4 Blades are whisper quiet, made of a carbon fiber composite with UV protectant, and intended for fast...

2 Inch Wind Turbine Mounting Bracket - 6 Hole Assembly

Zinc Plated Wind Turbine Mounting Bracket for 2 Inch PipeFixed bracket for Delco Style PMAs and the Freedom PMG and the Freedom II PMG Mounting Bracket Specifications: Mounting Bracket Height: 8 13/16 Inches (223.8 mm) Fits Tower Pole Size: 2 Inches...

25 Foot Freestanding Wind Turbine Tower

25 Foot Freestanding Wind Turbine Tower With Optional Jib - No Guy Wires Required Aluminum base with powder coated steel mast Four Legged Hinged Foot Pads Balanced – Can Run Freely Very Little Maintenance Includes lift bar with bridle Optional jib...

40 Foot Freestanding Wind Turbine Tower

40 Foot Freestanding Wind Turbine Tower With Optional Jib - No Guy Wires Required Aluminum base with powder coated steel mast Four Legged Hinged Foot Pads Balanced – Can Run Freely Very Little Maintenance Includes lift bar with bridle Optional jib...

Missouri Freedom 48 Volt 2000 Watt Wind Turbine and VRD Classic MPPT Kit

The Midnite Classic MPPT Wind Board can almost double your wind turbine's output at every wind speed over relay or PWM charge controllers. The incoming power from the wind turbine is routed through its own breaker, then converted by one of the most...

Missouri Freedom 24 Volt 2000 Watt Wind Turbine and VRD Classic MPPT Kit

Lithium Battery Compatible | MPPT Charging Technology The Midnite Classic MPPT Wind Board can almost double your wind turbine's output at every wind speed over relay based or PWM charge controllers. The incoming power from the wind turbine is routed...

SkyMax Energy Frontier PMG

SkyMax Energy Frontier 2000 Watt PMG with Optional Marine Coating* Assembled and supported in the USA, our Legacy and Frontier Wind Turbine PMGs are now designed with a keyed shaft and hub stabilizer as well as includes a self-tightening cam-lock washer...

17mm Shaft Nut

M17-1.25 Stainless Steel Hex Nut

Skymax Wind Sheer - Wind Grid Tie Inverter

Grid Tie Inverter Features:Easy installation - can be connected in parallel on AC sideLCD Display with Input Voltage, Output Power, Temperature, Power Curve, Output SinewaveThis inverter features an integrated rectifier inside the inverter that allows...

90 Amp 3 Wire Slip Ring Kit

90 Amp 3 Wire Slip Ring Kit for Wind Turbine Generators Kit Includes: (12) inches of 3/8 inch double wall heavy duty heat-shrink tube with air tight mastic inner seal (6) pieces 10-12 gauge butt connectors (1) 3 wire custom 90 amp AC/DC slip ring Get...

Short Bridge Aluminum Resistor Bar (Pair)

Short Bridge Aluminum Resistor Bars Use the short bridge aluminum resistor bar to connect two dump load resistors together as shown in the additional images. Product Specifications: 1 5/8 x 1 1/16 x 1/8 inches 4 grams  

Long Bridge Aluminum Resistor Bar

Long Bridge Aluminum Resistor Bars Use the long bridge aluminum resistor bars to connect four or more dump load resistors together. Product Specifications: 4 5/8 x 1 1/2 x 1/8 inches 22 grams Bars sold individually Two bridge bars can also be used to...

PMA Mounting Bracket and Tail Kit for Wind Turbine

PMA Mounting Bracket and Tail Kit for Wind Turbines Our Missouri Wind mounting bracket fits on 1 1/2 inch pipe (actual pipe OD is 1 7/8 inches). Perfect for building your own wind turbine. Only from Missouri Wind and Solar. Tail Kit Includes: Fixed...

Wind Turbine Tail Kit with Optional Mounting Bracket

Wind Turbine Tail Kit with Optional Mounting Bracket Made with all steel construction, this is the same tail we now use on our wind turbines at our store in Seymour, MO. We've added even more strength and stability by using the new arms which bolt to...

Raptor Generation 4 Wind Turbine Blade

Raptor Generation 4 (G4) Wind Turbine Blade Missouri Wind and Solar works hard to provide only the best products for our customers - introducing the original aerodynamic Raptor Generation 4 (G4) Blades. The Raptor G4 wind turbine blades are made from...

9 Raptor Generation 4 Wind Turbine Generator Blades and Hub

Set of 9 Raptor Generation 4 Blades and Zinc Plated Hub with Mounting Hardware 9 Blade Hub Specifications: Zinc plated (no painting required!) 3/16 inch (4.76 mm) thick steel 8 inch (203.2 mm) diameter Mounting holes are 1/4'' with 15/16'' hole center...

9 Blade Wind Turbine Hub with Optional Raptor Generation 4 Blade Set

Upgrade to 9 Blades 9 Blade Hub Specifications: Zinc plated (no painting required!) 3/16 inch (4.76 mm) thick steel 8 inch (203.2 mm) diameter Mounting holes are 1/4'' with 15/16'' hole center to center (.245" with .930" spacing) 17 mm hub center...

7 Raptor Generation 4 Wind Turbine Generator Blades and Hub

Set of 7 Raptor Generation 4 Blades and Zinc Plated Hub with Mounting Hardware 7 Blade Hub Specifications: Zinc plated (no painting required!) 3/16 inch (4.76 mm) thick steel 7 inch (177.8 mm) diameter Mounting holes are 1/4'' with 15/16'' hole...